Everything You need to Know about

ASTM B443

For more information, please visit HPE.

1. AEETHER
2. Blog
3. Alloy Knowledge

Overview

ASTM B443 specifies the technical requirements for Inconel 625 sheet, plate, coil and strip. Suppliers should strictly follow this standard when producing these materials. In this article, we will detail the noteworthy points and details in ASTM B443. This will help you make better decisions when purchasing and inspecting.

Product Properties

Products in ASTM B443

Inconel 625
Sheet

Inconel 625
Plate

Inconel 625
Coil

Inconel 625
Strip

ASTM B443 mainly includes four products: sheet, plate, coil and strip. The main way to distinguish them is size and production process. Generally speaking, the plate is thicker and is often produced by hot rolling. Sheet and strip are thinner and are often produced by cold rolling. Among them, the width of strip is narrower. Coil is a coiled sheet and plate. Its production process is determined by the thickness. The table below defines exactly how the different products differ.

Permissible Variations in Diameter or Distance
Between Parallel Surfaces of Cold-Worked Rod and Bar Product Thickness, in. (mm) Hot-rolled plate 3/16 (4.8) and over Cold-rolled plate 3/16 to 3/8 (4.8 to 9.5), incl Hot-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl Cold-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl Cold-rolled strip 0.005 to 0.250 (0.13 to 6.4), incl

Mechanical Properties

Room Temperature Tensile Properties and Heat Treatment Product Tensile
Strength, min,
ksi (MPa) Yield Strength
(0.2 % Offset),
min, ksi (MPa) Elongation in 2
in. or 50 mm (or
4D), min, % Grade I
UNS N (Annealed) Cold-rolled sheet and strip 120 (827) 60 (414) 30 Hot-rolled sheet and hot-rolled plate up to 2.75 in. (70 mm), incl 110 (758) 55 (379) 30 Cold-rolled plate up to 0.375 in. (9.5 mm), incl 110 (758) 55 (379) 30 Grade II
UNS N (Solution Annealed) Cold-rolled sheet and strip, hot-rolled sheet,
cold-rolled plate, and hot-rolled plate 100 (690) 40 (276) 30 All
UNS N (Solution Annealed) All plate, sheet, and strip 96 (660) 39 (270) 50

Delivery State

Inconel 625 is specified in two states in the standard: Grade I (Annealed) and Grade II (Solution Annealed). If not specified, the supplier shall deliver in Grade I state. Alloys in the Grade II state have better creep properties at high temperatures. Therefore, if your application requires the alloy to operate at high temperatures, delivery in the Grade II condition should be specified with the supplier in advance.

The standard stipulates that all UNS N alloys are delivered in a solution annealed state.

Other Information

Dimension

The standard specifies the tolerances for thickness, width and length of different products in detail. You can refer to the tables below:

Permissible Variations in Thickness and Overweight of Rectangular Plates Specified Thickness, in. (mm) Permissible Excess in Average Weight, B,C per Square Foot of Plates for Widths Given in Inches (Millimetres)
Expressed in Percent of Nominal Weights Under 48
() 48 to 60
( to
), excl 60 to 72
( to
), excl 72 to 84
( to
), excl 84 to 96
( to
), excl 96 to 108
( to
), excl 108 to 120
( to
), excl 120 to 132
( to
), excl 132 to 144
( to
), excl 144 to 160
( to
), excl 3/16 to 5/16 (4.8 to 7.9), excl 9.0 10.5 12.0 13.5 15.0 16.5 18.0 ... ... ... 5/16 to 3/8 (7.9 to 9.5), excl 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0 ... ... 3/8 to 7/16 (9.5 to 11.1), excl 7.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0 19.5 7/16 to 1/2 (11.1 to 12.7), excl 6.0 7.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0 1/2 to 5/8 (12.7 to 15.9), excl 5.0 6.0 7.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 5/8 to 3/4 (15.9 to 19.1), excl 4.5 5.5 6.0 7.0 7.5 9.0 10.5 12.0 13.5 15.0 3/4 to 1 (19.1 to 25.4), excl 4.0 4.5 5.5 6.0 7.0 7.5 9.0 10.5 12.0 13.5 1 to 2 (25.4 to 50.8), incl 4.0 4.0 4.5 5.5 6.0 7.0 7.5 9.0 10.5 12.0 Permissible Variations in Thickness for Rectangular Plates Over 2 in. (51 mm) in Thickness Specified Thickness, in. (mm) Permissible Variations, in. (mm), over Specified Thickness for Widths Given, in. (mm) To 36 (915), excl 36 to 60
(915 to
), excl 60 to 84
( to
), excl 84 to 120
( to
), excl 120 to 132
( to
), excl 132 (
and over) Over 2 to 2 3/4 (51 to 69.8), incl 1/16 (1.6) 3/32 (2.4) 7/64 (2.8) 1/8 (3.2) 1/8 (3.2) 9/64 (3.6) Permissible Variations in Thickness of Sheet and Strip Specified Thickness, in. (mm), incl Sheet Hot-Rolled Cold-Rolled 48 () and Under Over 48 to 60 ( to ), incl 48 () and Under Over 48 to 60 ( to ), incl 0.018 to 0.025 (0.5 to 0.6) 0.003 (0.08) 0.004 (0.10) 0.002 (0.05) 0.003 (0.08) Over 0.025 to 0.034 (0.6 to 0.9) 0.004 (0.10) 0.005 (0.13) 0.003 (0.08) 0.004 (0.10) Over 0.034 to 0.043 (0.9 to 1.1) 0.005 (0.13) 0.006 (0.15) 0.004 (0.10) 0.005 (0.13) Over 0.043 to 0.056 (1.1 to 1.4) 0.005 (0.13) 0.006 (0.15) 0.004 (0.10) 0.005 (0.13) Over 0.056 to 0.070 (1.4 to 1.8) 0.006 (0.15) 0.007 (0.18) 0.005 (0.13) 0.006 (0.15) Over 0.070 to 0.078 (1.8 to 1.9) 0.007 (0.18) 0.008 (0.20) 0.006 (0.15) 0.007 (0.18) Over 0.078 to 0.093 (1.9 to 2.4) 0.008 (0.20) 0.009 (0.23) 0.007 (0.18) 0.008 (0.20) Over 0.093 to 0.109 (2.4 to 2.8) 0.009 (0.23) 0.010 (0.25) 0.007 (0.18) 0.009 (0.23) Over 0.109 to 0.125 (2.8 to 3.2) 0.010 (0.25) 0.012 (0.31) 0.008 (0.20) 0.010 (0.25) Over 0.125 to 0.140 (3.2 to 3.6) 0.012 (0.31) 0.014 (0.36) 0.008 (0.20) 0.010 (0.25) Over 0.140 to 0.171 (3.6 to 4.3) 0.014 (0.36) 0.016 (0.41) 0.009 (0.23) 0.012 (0.31) Over 0.171 to 0.187 (4.3 to 4.8) 0.015 (0.38) 0.017 (0.43) 0.010 (0.25) 0.013 (0.33) Over 0.187 to 0.218 (4.8 to 5.5) 0.017 (0.43) 0.019 (0.48) 0.011 (0.28) 0.015 (0.38) Over 0.218 to 0.234 (5.5 to 5.9) 0.018 (0.46) 0.020 (0.51) 0.012 (0.31) 0.016 (0.41) Over 0.234 to 0.250 (5.9 to 6.4) 0.020 (0.51) 0.022 (0.56) 0.013 (0.33) 0.018 (0.46) Cold-Rolled Specified Thickness, in. (mm), incl Widths 12 in. (305 mm) and under, plus and minus Up to 0.050 (1.27), incl 0. (0.038) Over 0.050 to 0.093 (1.27 to 2.39) 0. (0.063) Over 0.093 to 0.125 (2.39 to 3.18) 0.004 (0.11) Permissible Variations in Width of Sheared, Plasma Torch-Cut, and Abrasive-Cut Rectangular Plate Specified Thickness Permissible Variations in Widths for Widths Given, in. (mm) Up to 30 (760), incl Over 30 to 72 (760 to ), incl Over 72 to 108 ( to ), incl Over 108 to 144 ( to ), incl Over 144 to 160 ( to ), incl Plus Minus Plus Minus Plus Minus Plus Minus Plus Minus Inches Sheared: 3/16 to 5/16, excl 3/16 1/8 1/4 1/8 3/8 1/8 1/2 1/8 ... ... 5/16 to 1/2, excl 1/4 1/8 3/8 1/8 3/8 1/8 1/2 1/8 5/8 1/8 1/2 to 3/4, excl 3/8 1/8 3/8 1/8 1/2 1/8 5/8 1/8 3/4 1/8 3/4 to 1, excl 1/2 1/8 1/2 1/8 5/8 1/8 3/4 1/8 7/8 1/8 1 to 1 1/4, incl 5/8 1/8 5/8 1/8 3/4 1/8 7/8 1/8 1 1/8 Abrasive-cut: 3/16 to 1 1/4, incl 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 Over 1 1/4 to 2 3/4, incl 3/16 1/8 3/16 1/8 3/16 1/8 3/16 1/8 3/16 1/8 Plasma torch-cut: 3/16 to 2, excl 1/2 0 1/2 0 1/2 0 1/2 0 1/2 0 2 to 2 3/4, incl 5/8 0 5/8 0 5/8 0 5/8 0 5/8 0 Millimetres Sheared: 4.8 to 7.9, excl 4.8 3.2 6.4 3.2 9.5 3.2 12.7 3.2 ... ... 7.9 to 12.7, excl 6.4 3.2 9.5 3.2 9.5 3.2 12.7 3.2 15.9 3.2 12.7 to 19.1, excl 9.5 3.2 9.5 3.2 12.7 3.2 15.9 3.2 19.1 3.2 19.1 to 25.4, excl 12.7 3.2 12.7 3.2 15.8 3.2 19.1 3.2 22.2 3.2 25.4 to 31.8, incl 15.9 3.2 15.9 3.2 19.1 3.2 22.2 3.2 25.4 3.2 Abrasive-cut: 4.8 to 31.8, incl 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 Over 31.8 to 69.8, incl 4.8 3.2 4.8 3.2 4.8 3.2 4.8 3.2 4.8 3.2 Plasma torch-cut: 4.8 to 50.8, excl 12.7 0 12.7 0 12.7 0 12.7 0 12.7 0 50.8 to 69.8, incl 15.9 0 15.9 0 15.9 0 15.9 0 15.9 0 Permissible Variations in Diameter for Circular Plates Sheared Plate Specified Diameter, in. (mm) Permissible Variations Over Specified Diameter for Thickness Given, in. (mm) To 3&#;8 (9.5), incl 20 to 32 (508 to 813), excl 1/4 (6.4) 32 to 84 (813 to ), excl 5/1 6 (7.9) 84 to 108 ( to ), excl 3/8 (9.5) 108 to 140 ( to ), incl 7/16 (11.1) Plasma Torch-Cut Plate Specified Diameter, in. (mm) Permissible Variations in Specified Diameter for Thickness Given, in. (mm) Thickness max, in. (mm) 3/16 to 2 (4.8 to 50.8), excl 2 to 2-3/4 (50.8 to 69.8), incl Plus Minus Plus Minus 19 to 20 (483 to 508), excl 2-3/4 (69.8) 1/2 (12.7) 0 5/8 (15.9) 0 0 to 22 (508 to 559), excl 2-3/4 (69.8) 1/2 (12.7) 0 5/8 (15.9) 0 2 to 24 (559 to 610), excl 2-1/2 (63.5) 1/2 (12.7) 0 5/8 (15.9) 0 4 to 28 (610 to 711), excl 2-1/4 (57.3) 1/2 (12.7) 0 5/8 (15.9) 0 8 to 32 (711 to 812), excl 2 (50.8) 1/2 (12.7) 0 5/8 (15.9) 0 2 to 34 (812 to 864), excl 1-3/4 (44.5) 1/2 (12.7) 0 ... ... 4 to 38 (864 to 965), excl 1-1/2 (38.1) 1/2 (12.7) 0 ... ... 8 to 40 (965 to ), excl 1-1/4 (31.8) 1/2 (12.7) 0 ... ... 0 to 140 ( to ), incl 2-3/4 (69.8) 1/2 (12.7) 0 5/8 (15.9) 0 Permissible Variations in Width of Sheet and Strip Specified Thickness, in. (mm) Specified Width, in. (mm) Permissible Variations in Specified Width, in. (m) Plus Minus Sheet Up to 0.250 (6.35) All 0.125 (3.18) 0 Strip Under 0.075 (1.9) Up to 12 (305), incl 0.007 (0.18) 0.007 (0.18) Over 12 to 48 (305 to ), incl 0.062 (1.6) 0 0.075 to 0.100 (1.9 to 2.5), incl Up to 12 (305), incl 0.009 (0.23) 0.009 (0.23) Over 12 to 48 (305 to ), incl 0.062 (1.6) 0 Over 0.100 to 0.125 (2.5 to 3.2), incl Up to 12 (305), incl 0.012 (0.30) 0.012 (0.30) Over 12 to 48 (305 to ), incl 0.062 (1.6) 0 Over 0.125 to 0.160 (3.2 to 4.1), incl Up to 12 (305), incl 0.016 (0.41) 0.016 (0.41) Over 12 to 48 (305 to ), incl 0.062 (1.6) 0 Over 0.160 to 0.187 (4.1 to 4.7), incl Up to 12 (305), incl 0.020 (0.51) 0.020 (0.51) Over 12 to 48 (305 to ), incl 0.062 (1.6) 0 Over 0.187 to 0.250 (4.7 to 6.4), incl Up to 12 (305), incl 0.062 (1.6) 0.062 (1.6) Over 12 to 48 (305 to ), incl 0.062 (1.6) 0.062 (1.6) Permissible Variations in Length of Sheared, Plasma Torch-Cut, and Abrasive-Cut Rectangular Plate Specified Thickness Permissible Variation in Length for Lengths Given, in. (mm) Up to 60 (), incl Over 60 to 96 ( to ), incl Over 96 to 120 ( to ), incl Over 120 to 240 ( to ), incl Over 240 to 360 ( to ), incl Over 360 to 450 ( to 11 430), incl Over 450 to 540 (11 430 to 13 716), incl Over 540 (13 716) Plus Minus Plus Minus Plus Minus Plus Minus Plus Minus Plus Minus Plus Minus Plus Minus Inches Sheared: 3/16 to 5/16, excl 3/16 1/8 1/4 1/8 3/8 1/8 1/2 1/8 5/8 1/8 3/4 1/8 7/8 1/8 ... ... 5/16 to 1/2, excl 3/8 1/8 1/2 1/8 1/2 1/8 1/2 1/8 5/8 1/8 3/4 1/8 7/8 1/8 1 1/8 1/2 to 3/4, excl 1/2 1/8 1/2 1/8 5/8 1/8 5/8 1/8 3/4 1/8 7/8 1/8 1-1/8 1/8 1-3/8 1/8 3/4 to 1, excl 5/8 1/8 5/8 1/8 5/8 1/8 3/4 1/8 7/8 1/8 1-1/8 1/8 1-3/8 1/8 1-5/8 1/8 1 to 1-1/4, incl 3/4 1/8 3/4 1/8 3/4 1/8 7/8 1/8 1-1/8 1/8 1-3/8 1/8 1-5/8 1/8 ... ... Abrasive-cut: 3/16 to 1-1/4, incl 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 ... ... ... ... Over 1-1/4 to 2-3/4, incl 3/16 1/8 3/16 1/8 3/16 1/8 3/16 1/8 3/16 1/8 3/16 1/8 ... ... ... ... Plasma torch-cut: 3/16 to 2, excl 1/2 0 1/2 0 1/2 0 1/2 0 1/2 0 1/2 0 1/2 0 1/2 0 2 to 2-3/4 5/8 0 5/8 0 5/8 0 5/8 0 5/8 0 5/8 0 5/8 0 5/8 0 Millimetres Sheared: 4.8 to 7.94, excl 4.8 3.2 6.4 3.2 9.5 3.2 12.7 3.2 15.9 3.2 19.0 3.2 22.2 3.2 ... ... 7.94 to 12.7, excl 9.5 3.2 12.7 3.2 12.7 3.2 12.7 3.2 15.9 3.2 19.0 3.2 22.2 3.2 25.4 3.2 12.7 to 19.0, excl 12.7 3.2 12.7 3.2 15.9 3.2 15.9 3.2 19.0 3.2 22.2 3.2 28.6 3.2 34.9 3.2 19.0 to 25.4, excl 15.9 3.2 15.9 3.2 15.9 3.2 19.0 3.2 22.2 3.2 28.6 3.2 34.9 3.2 41.2 3.2 25.4 to 31.8, incl 19.0 3.2 19.0 3.2 19.0 3.2 22.2 3.2 28.6 3.2 34.9 3.2 41.2 3.2 ... ... Abrasive-cut: 4.8 to 31.8, incl 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 ... ... ... ... Over 31.8 to 69.9, incl 4.8 3.2 4.8 3.2 4.8 3.2 4.8 3.2 4.8 3.2 4.8 3.2 ... ... ... ... Plasma torch-cut: 4.8 to 50.8, excl 12.7 0 12.7 0 12.7 0 12.7 0 12.7 0 12.7 0 12.7 0 12.7 0 50.8 to 69.8, incl 15.9 0 15.9 0 15.9 0 15.9 0 15.9 0 15.9 0 15.9 0 15.9 0

Flatness

ASTM B443 also specifies flatness tolerances for plates. This requires suppliers to fine-tune equipment during hot rolling.

Permissible Variations From Flatness of Rectangular, Circular, and Sketch Plates Specified Thickness Permissible Variations from a Flat Surface for Thickness and Widths Given, in. (mm) To 48
(), excl 48 to 60
( to
), excl 60 to 72
( to
), excl 72 to 84
( to
), excl 84 to 96
( to
), excl 96 to 108
( to
), excl 108 to 120
( to
), excl 120 to 144
( to
), excl 144
()
and over Inches 3/16 to 1/4, excl 1-1/2 2-1/8 2-1/2 2-3/4 3-1/4 3-1/4 ... ... ... 1/4 to 3/8, excl 1-3/8 1-1/2 1-7/8 2-1/4 2-3/4 2-7/8 3-1/8 3-3/4 ... 3/8 to 1/2, excl 1 1-1/8 1-3/8 1-1/2 1-7/8 2-1/4 2-1/2 2-7/8 3-1/2 1/2 to 3/4, excl 1 1-1/8 1-1/4 1-1/4 1-5/8 2-1/4 2-1/4 2-1/4 2-3/4 3/4 to 1, excl 1 1-1/8 1-1/4 1-1/4 1-1/2 1-5/8 1-7/8 2 2-1/4 1 to 2, excl 1 1-1/8 1-1/8 1-1/8 1-3/8 1-3/8 1-3/8 1-1/2 2 2 to 2-3/4, incl 1/2 5/8 3/4 7/8 1 1-1/8 1-1/4 1-1/2 1-3/4 Millimetres 4.8 to 6.4, excl 38.1 54.0 63.5 69.8 82.6 82.6 ... ... ... 6.4 to 9.5, excl 34.9 38.1 47.6 57.2 69.8 73.0 79.4 95.2 ... 9.5 to 12.7, excl 25.4 28.6 34.9 38.1 47.6 57.2 63.5 73.0 88.9 12.7 to 19.0, excl 25.4 28.6 31.8 31.8 41.3 57.2 57.2 57.2 69.8 19.0 to 25.4, excl 25.4 28.6 31.8 31.8 38.1 41.3 47.6 50.8 57.2 25.4 to 50.8, excl 25.4 28.6 28.6 28.6 34.9 34.9 34.9 38.1 50.8 50.8 to 70.0, incl 12.7 15.9 19.0 22.2 25.4 28.6 31.8 38.1 44.4

Straightness

The edgewise curvature (depth of chord) of flat sheet, strip, and plate shall not exceed 0.05 in. (1.27 mm) multiplied by the length in feet (0.04 mm multiplied by the length in centimeters).

Edges

Sheet and strip shall have sheared or slit edges. Plate shall have sheared or cut (machined, abrasive cut, powder cut, or inert arc cut) edges, as specified.

If you are looking for more details, kindly visit inconel 625 tubing.

Squareness

For sheets of all thicknesses, the angle between adjacent sides shall be 90 ± 0.15° (1/16 in. in 24 in., 1.6 mm in 610 mm).

Certification

The supplier shall provide the material test certificate corresponding to the material before delivery. The certificate should include supplier and customer information, product size and delivery state, chemical composition and mechanical properties, size, standard and heat number.

Conclusion

ASTM B443 is mainly applicable to Inconel 625 sheets. The standard stipulates the chemical composition, mechanical properties, and dimensional tolerances of materials. Suppliers shall produce materials in strict accordance with standards.

We can produce Inconel 625 sheet, plate and strip according to the standard of ASTM B443. If you have any needs, you can contact us.

Nickel Alloy 625 / Inconel 625®

Technical Data Sheet

Alloy 625 (UNS N) is a nickel-chromium-molybdenum alloy with an addition of niobium. The addition of molybdenum acts with the niobium to stiffen the alloy matrix, providing a high strength without a strengthening heat treatment. The alloy resists a wide range of corrosive environments and has a good resistance to pitting and crevice corrosion. Alloy 625 is used in chemical processing, aerospace and marine engineering oil & gas, pollution control equipment and nuclear reactors.

Chemical Composition Limits Weight % Ni Cr Mo Nb + Ta Fe Ti C Mn Si S P Al Co Alloy 625 58.0 min 20 - 23 8 -10 3.15 -4.15 5.0 max 0.40 max 0.10 max 0.50 max 0.50 max 0.15 max 0.15 max 0.40 max 1.0 max

Typical Mechanical Properties

Material Form and Condition Tensile Strength MPa Yield Strength (0.2% Offset) MPa Elongation 4D(%) Hardness HB Ksi MPa Ksi MPa Alloy 625 Bar Annealed 120 827 60 414 30 &#; 287 HB Alloy 625 Sheet Annealed 120 827 60 414 30 145-240 Alloy 625 Tube
Seamless and Welded Annealed 120 827 60 414 35 -

Availability
Alloy 625 (UNS N) is available in Round Bar, Flat Bar, Extruded section, Pipe, Tube, Plate, Sheet, Strip, Plate, Hexagon, Forging Stock, Extruded Section, Wire and Powder. View Stock List, Plate Stock List or contact Sales for further availability.

NEW - Aircraft Materials now offers a comprehensive range of high-quality alloy 625 metal powders, produced and tested to exacting standards for use in all processes including Additive Manufacturing (AM), Near-Net Shape Powder Metallurgy (NNS/PS) and Hot-Isostatic Pressing (HIP). Find out more us with your quality alloy 625 metal powder requirements:

Specifications

Bar ASTM B 446, ASME SB 466, AMS , ISO , VdTUV 499, BS NA21, EN , DIN , ASME Code Case Rod ASTM B 446, ASME SB 466, ISO , VdTUV 499, BS NA21, EN , DIN , SME Code Case Wire AMS , ISO , DIN Forging Stock ASTM B 564, ASME SB 564, AMS , ISO , SME Code Case , DIN Plate ASTM B 443, ASME SB 443, AMS , AMS , MAM , ISO , VdTUV 499, BS NA21, EN , DIN , ASME Code Case
Sheet ASTM B 443, ASME SB 443, AMS , AMS , MAM , ISO , VdTUV 499, BS NA21, EN , DIN , ASME Code Case
Strip ASTM B 443, ASME SB 443, AMS , AMS , MAM , ISO , VdTUV 499, EN , DIN , ASME Code Case Pipe Seamless ASTM B444, ASTM B829, ASME SB 444, ASME SB 829, BS NA21 Pipe Welded ASTM B705, ASTM B775, ASME SB 705, ASME SB 775 Tube Seamless ASTM B444, ASTM B829, ASME SB 444, ASME SB 829, AMS , BS NA21, AMS Type 1 Tube Welded ASTM B704, ASTM B751, ASME SB 704, ASME SB 704, AMS , AMS Type 2 Tube VdTUV 499, ISO , DIN , ASME Code Case Fittings ASTM B 366, ASME SB 366 Powder ASTM F, AMS Other UNS N, W. Nr 2., ISO NW, NACE MR-01-75, INCONEL 625 (trademark), MSRR

 

Customer Reviews - What Customers Say About Us!

"Just wanted to say thanks for your efforts and updates"

"I always try you as you often keep stock that can't be found elsewhere"

"Prompt answer & knowledge of available material, timescale & price within a good time"

"Packaging is superb"

"Thank you for your quick response"

Disclaimer
Every effort is made to ensure that technical specifications are accurate. However, technical specifications included herein should be used as a guideline only. All specifications are subject to change without notice.

 

If you want to learn more, please visit our website astm a511 stainless steel hollow bar wholesale.